JeeHell FMGS forums

Hi JL, I'm using VOXATC and it is installed on the P3D Computer. But it isn't an external application. VoxATC loads with the P3D via dll.xml. So the intercom and the receiving app runs on the same computer, as you describe. P3D and Starter runs both with administrator rights. But the RAD switch does...

I don't understand your comment Jean Luc.
Do you mean, the ACP Panel must connected to the same computer were the intercom is running?

Hi Micha,

do you use the skalarki Hardware?
Then the Profiler is started to quick or bevor the Jeehell server is fully loaded.

Hi all, one question. In the Intercomm App I can assign a PTT Key. This Key is sent when I press the ACP RAD Switch? In my configuration in the Intercom App the PTT key is "End" Key In my ATC App the PTT Key is "END" Key too. But if I press the RAD switch on the ACP nothing appea...

Hi Stephan,
hi Bernd,

if I assume that you are using real tillers, then you could replace the linear potentiometer with a logarithmic potentiometer.
So the curve would change and should roughly correspond to the required effect?

Hi all, so after spending hours of checking my configuration I found the error. I switched from P3Dv4 to P3Dv5 some time ago. The asconnect_64.dll from Active Sky 4 was left over in the dll.xml. Thus the dll files for v4 and v5 were both loaded. Of course I've changed that now and the weather radar ...

Hello all, I have now completely checked my setup and cannot find any configuration error. After all, it worked before. I just have no idea anymore where to look for errors. I have no other problems at all, everything works as it should. Even the ground radar works. I can't say exactly when it stopp...

Hi Stephan, the installation is as follows: 1 computer "FMGS server" 1 computer "P3D" 1 computer "PFD/ND" 1 "Active Sky" computer The WXR folder is released on the P3D computer and has read and write rights. The folder for the P3D WXR folder is shared to the P...

hello dieter Have you defined this in asp3d under General options - Common data export path? Hi Stephan, no I have not set that. I am also of the opinion that it is not necessary. Since Active Sky is installed on a separate computer with TopCat and I need the data from this folder for TopCat, I did...

hi all, I need your help. My weather radar isn't working anymore. I use ASP3D with the P3Dv5.4. Active Sky is not installed on the P3D PC, so I installed the tool ASP3DV5ConnectorInstall. This replaces the earlier Simconnect. The WXR folder is released on the P3D PC and also has read and write right...

Hi Andrew,

you can test the Buttons in Profiler, also the trim wheel.
The Profiler for the Pedestal PC must show all green.
If the MCDUs are working, then check the loaded profile if it has the right assignments.
And, what buttons du you mean, ENG Start?

Hi JL,

yes, I have set the freq of Cologne to 132.130 in the AFCAD.
I understand your comment for VOR, but why are the Navigraph Charts give us frequencies in this space for other Airports?
Is this an error from Navigraph or are these frequencies really so now?
I'm confused.

First, what is your name? Then one can also address you, which would be quite nice Your setup is not unusual, I use about the same setup with several computers. For this to work, the IP addresses on all machines must be correct during the setup of Jeehell. Also your network must work correctly. Mean...

Hi all, I would like to add something to the problem, because I noticed it in the last few days. In Cologne the current ATIS frequency is 112.150 In Krakow it is 112.800 In Manchester it is 113.550 To give three examples. However, it is not possible to turn in frequencies below 118.000 in the RMP at...

Hi Bernd, yes, you are right.
I have uninstalled Vector and I don't see any big differences visually.

Hi Jean Luc, your explanation seems conclusive to me. I have tested it by disabling ORBX Vector. After restarting all the computers, I then loaded a flight plan that causes this problem. The time to load is less than 30 seconds (before 4 min) and there is also no disconnection to the Jeehell server....

Hi Jean Luc, I found a new problem when the Jeehell server is installed on a second machine. If you have installed many addons and switch off an addon via the P3D menu, the scenery index is recreated in the P3D and the entire scenery is reloaded. However, this can sometimes take a little longer. For...

But I'm glad I'm not the only one having this problem. I have a Navigraph subscription and cannot use the frequencies on the current charts. If VATSIM and others change over now, that will be a bigger problem. I think that Jean Luc should react much faster to this. Especially since we can already de...

Hi Berry,

I'm not shure what you do. But I have downloaded the latest version.
Install it on a test machine and I have in navdata folder the file FSscenery.cfg
There is no missing file.

Hi Berry, as Bernd has already written. Do it on the P3D computer. I have long ago programmed the tool UPDNAV for these cases. This is adapted to the latest versions of JL. With this you can create the *.BGL files on the P3D computer and then distribute them automatically to the rest of the computer...

]Today I read the offsets from FSUIPC. Obviously the active frequency is not always filled or read correctly.
The standby frequency is not used at all in 32 bits.
I took two screenshots of the RMP and the offsets.

Hi Bernd, I think JL uses the FSUIPC offsets. Since other programs react to the frequencies turned in, this must actually be passed on to the simulator via FSUIPC. And exactly there is the problem of the new offsets for the 6 digit frequencies. I suspect that JL still fills the old 16 bit BCD offset...

Hi JL,

thanks for your answer.
How do you read or set the frequencies from/to the simulator?
If I can help, let me know.

Hi Jean Luc, today I do some test with frequencies on EDDL. I change the ground frequencies from 121.600 to .605, .610, .615, .625, .630, .635 Only .600 and .625 are working. I think the rest is in 25 khz steps too. The FMGS Server option is set to 8.33 khz. I have tested with the software panel too...

I don't know if it helps. But since FSUIPC v6 there ar new Offsets for frequencys in 8.33 khz space 05C4 Active COM1 frequency in Hz (32 bit int) 05C8 Active COM2 frequency in Hz (32 bit int) 05CC Standby active COM1 frequency in Hz (32 bit int) 05D0 Standby COM2 frequency in Hz (32 bit int) The old...